Load data for .260 PICRA + .264 | 155gr | CutEdge DGSC

Recommended Powder(s): Accurate No. 11 FS, Somchem S265

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.264 \| 155gr \| CutEdge DGSC
Manufacturer SKU:	DGSC G155
Bullet Weight:	155gr \| 10.0g
Bullet Diameter:	0.264" \| 6.71mm
Bullet Length:	1.372" \| 34.8mm
Caliber:	.260 PICRA load data
Case Length (l3):	1.515" \| 38.5mm
Cartridge Length (C.O.L.):	2.404" \| 61.1mm
Seated Depth:	0.483" \| 12.3mm
Shank Seated Depth:	0.483" \| 12.3mm
Case Capacity:	38.6 Grains of Water \| 2.51 cm³
Primer Size:	Large Pistol (LP)
Max. allowed Pressure:	56565 psi \| 3900 bar
LID:	LID_B8435_C251
Last updated:	2025-01-01

Load data for 46 loads in caliber .260 PICRA with .264 | 155gr | CutEdge DGSC bullet and 23 powders such as Accurate No. 11 FS, Somchem S265. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	67%	50546	89%	**22	100%
ADI APS 350	<<locked>>	72%	49168	87%	**61	101%
ADI APS 450	<<locked>>	73%	50647	90%	**81	100%
ADI AS 30	<<locked>>	69%	50705	90%	**91	100%
Accurate No. 11 FS 👍	<<locked>>	66%	49661	88%	**40	99%
Accurate Solo 1000	<<locked>>	65%	49980	88%	**01	100%
Accurate Solo 1250	<<locked>>	63%	50227	89%	**17	100%
Baschieri & Pellagri 100	<<locked>>	63%	50299	89%	**91	100%
Hodgdon Clays	<<locked>>	72%	50778	90%	**75	100%
Hodgdon TrailBoss	<<locked>>	95%	31966	57%	**8	100%
Maxam CSB 1	<<locked>>	66%	50821	90%	**17	100%
Maxam CSB 3	<<locked>>	65%	50299	89%	**04	100%
Maxam CSB 4	<<locked>>	63%	48994	87%	**88	100%
Maxam CSB 5	<<locked>>	65%	50227	89%	**84	100%
ReloadSwiss RS 14	<<locked>>	95%	32082	57%	**4	100%
ReloadSwiss RS 30	<<locked>>	74%	49792	88%	**44	100%
SNPE Vectan A0	<<locked>>	63%	49777	88%	**37	100%
SNPE Vectan BA10	<<locked>>	68%	50647	90%	**81	100%
SNPE Vectan BA6 1/2	<<locked>>	79%	50299	89%	**01	100%
SNPE Vectan BA7 1/2	<<locked>>	64%	50792	90%	**89	100%
Somchem S265 👍	<<locked>>	71%	49443	87%	**30	100%
Vihtavuori N110	<<locked>>	70%	49617	88%	**11	100%
Vihtavuori N32C Tin Star	<<locked>>	86%	49850	88%	**52	100%

Max Load - Barrel Length: 5.50''

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	61%	43105	76%	**47	100%
ADI APS 350	<<locked>>	61%	39871	70%	**56	100%
ADI APS 450	<<locked>>	61%	39856	70%	**70	100%
ADI AS 30	<<locked>>	61%	42888	76%	**15	100%
Accurate No. 11 FS	<<locked>>	61%	41626	74%	**45	98%
Accurate Solo 1000	<<locked>>	61%	45977	81%	**58	100%
Accurate Solo 1250	<<locked>>	61%	48153	85%	**94	100%
Baschieri & Pellagri 100	<<locked>>	61%	48298	85%	**68	100%
Hodgdon Clays	<<locked>>	61%	41147	73%	**79	100%
Hodgdon TrailBoss	<<locked>>	61%	17796	31%	**1	100%
Maxam CSB 1	<<locked>>	61%	45034	80%	**58	100%
Maxam CSB 3	<<locked>>	61%	46340	82%	**68	100%
Maxam CSB 4	<<locked>>	61%	47021	83%	**65	100%
Maxam CSB 5	<<locked>>	61%	46267	82%	**42	100%
ReloadSwiss RS 14	<<locked>>	61%	18014	32%	**8	100%
ReloadSwiss RS 30	<<locked>>	61%	32750	58%	**27	99%
SNPE Vectan A0	<<locked>>	61%	47863	85%	**17	100%
SNPE Vectan BA10	<<locked>>	61%	43366	77%	**12	100%
SNPE Vectan BA6 1/2	<<locked>>	61%	30066	53%	**45	100%
SNPE Vectan BA7 1/2	<<locked>>	61%	47079	83%	**47	100%
Somchem S265	<<locked>>	61%	36201	64%	**50	98%
Vihtavuori N110	<<locked>>	61%	37826	67%	**76	100%
Vihtavuori N32C Tin Star	<<locked>>	61%	30879	55%	**5	100%

Start Load - Barrel Length: 5.50''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data